Maintenance· November 18, 2026

How to descale a Breville Barista Express

A step-by-step descaling guide for the Breville Barista Express (BES870 / BES870XL), taken from the official instruction book and Breville’s US support pages — including the difference between a solid and a flashing CLEAN / DESCALE light.

Affiliate disclosure. As an Amazon Associate I earn from qualifying purchases.Crema Desk may earn a commission if you buy through links on this page. We do not invent product tests. See the full affiliate disclosure.

The Barista Express is one of the most widely owned home espresso machines. Scale is not a cosmetic issue on this machine. Breville’s official BES870 instruction book states that, after regular use, hard water can cause mineral buildup on inner components, reducing brewing flow, brewing temperature, power, and the taste of the espresso.

This guide walks through the official descaling procedure for the Barista Express models BES870 and BES870XL. It is based on that instruction book and on Breville’s US support pages for the same model family. It is not a personal test log, and it is not a substitute for the booklet that shipped with your machine. If the printed manual in your box differs, follow the booklet and the model number on the rating plate.

If you own a Barista Express Impress, Barista Touch, Oracle, or another Breville or Sage model, stop here and use that model’s manual. The button combination and the meaning of the lights are not identical across the range. In the United Kingdom and some other markets the Barista Express is sold under the Sage brand; check the model number, not only the marketing name, before you start.

Solid light or flashing light?

The same CLEAN / DESCALE indicator on the Barista Express means two different jobs. Mixing them up is the most common way to start the wrong procedure.

  • Solid (steadily on): Breville says descaling is required. Use the descale steps below.
  • Flashing: That is the cleaning cycle, not descaling. The instruction book says this light “will automatically illuminate (flashing) to indicate when a cleaning cycle is required.” The cleaning cycle uses a cleaning tablet, runs for approximately five minutes, and ends with two beeps. It is meant to clear coffee oils from the brew path. It does not replace a descale, and a descale does not replace it.

If the light is flashing, run the cleaning cycle described in the BES870 book (the cleaning-cycle section, around page 24 in the ANZ instruction book cited below). Come back to this guide when the light is solid, or when you are descaling on a schedule because of hard water.

What scale is, and why all three circuits matter

Espresso machines heat and push water through narrow paths: the brew boiler or thermocoil and group, the steam wand, and the hot-water outlet. Minerals that are dissolved in tap water — mostly calcium and magnesium carbonates in hard water — come out of solution when the water is heated and cling to those surfaces. The official book’s list of consequences is practical, not poetic: slower flow, less stable temperature, weaker performance, and worse-tasting espresso.

A descale has to reach every path that carries heated water. That is why the official procedure is not “run a tank of solution through the group head and stop.” You descale the coffee circuit, then steam, then hot water, and you do that pass twice so the tank of solution is actually used, then you repeat the same three stages with clean water so you are not brewing the next shot through leftover descaler.

The built-in conical grinder is a separate system. Descaling treats water paths. Burrs collect coffee oil and fines. The instruction book has a 12-step sequence for unlocking the hopper and brushing the upper and lower burrs. Do not pour descaling solution into the bean hopper.

What you need

  • One sachet of Breville Descaling powder. The official procedure is specific: dissolve one sachet into one litre of water, then fill the water tank. This guide does not recommend a substitute, because the BES870 descaling section does not describe one.
  • A way to catch water from the group head, the steam wand, and the hot-water outlet — the drip tray plus a heat-safe container if you want extra capacity.
  • Fresh cold drinking water for the rinse, enough to fill the tank to its 2 litre maximum.
  • About 15–20 minutes in which you can stay next to the machine. The individual stages are short (about 25 seconds for the coffee circuit, 13 seconds for steam, and 8 seconds for hot water), but you will run them more than once, and the machine also needs a short heat-up after you enter Descale mode.

Breville’s US support page for the Barista Express water filter says the included filter is rated for 60 days or 10.6 gallons, at which point you need to replace it. The instruction book says replacing the filter every two months will reduce the need to descale, and that if you live in a hard water area you should change the filter more often. A fresh filter slows scale; it does not make descaling unnecessary.

Warnings from the manufacturer

Copy these as they appear in spirit in the official book, and do not skip them to save a minute:

  • Do not immerse the power cord, power plug, or appliance in water or any other liquid.
  • The water tank should never be removed or completely emptied during descaling.
  • Remove the water filter from the tank before you add descaling powder.

Leaving the filter in the tank while you add powder can damage the filter and put descaler where it does not belong. Lifting the tank off in the middle of the cycle can interrupt the process. If you are tempted to use vinegar, citric acid from a pantry jar, or another generic descale liquid because it is already in the cupboard: the official procedure specifies Breville Descaling powder. This article stays with that instruction.

Prepare the machine

Clear the drip tray. Have a towel for the steam wand. Confirm you are looking at a Barista Express with the familiar POWER, 1-CUP, 2-CUP, and steam / hot-water dial, not a later “Impress” control panel.

If a portafilter is locked in the group, remove it. You want the solution to run freely through the group head. Take the water filter out of the tank and set it in a clean cup — you will put a filter back after the rinse, not into the descaling solution.

The instruction book’s filter-conditioning steps, for when you later install a new filter, are: soak the new filter in a cup of water for 5 minutes, rinse it under cold running water for 5 seconds, insert it into the filter holder, set the date dial two months ahead, and push down to lock it in the tank. You can do that after the descale, not before it.

Official descale procedure

These steps follow the BES870 instruction book.

1. Confirm that you need a descale, not a clean. Check that the CLEAN / DESCALE light is illuminated and solid.

2. Mix the solution and fill the tank. Dissolve one Breville Descaling powder sachet into one litre of water, then fill the water tank with that solution. (The filter is already out.)

3. Enter Descale mode. Press and hold the 2-CUP button, then press and hold the POWER button at the same time. The unit heats as it starts the descaling action; the POWER button should flash continuously during heating. The machine is ready when four indicators are all solid: POWER, 1-CUP, CLEAN / DESCALE, and HOT WATER / STEAM.

If you do nothing for five minutes, the machine turns itself off automatically. The book is explicit: to resume, start again from this step (step 3 in the manual — entering Descale mode).

4. Descale the coffee circuit. Press 1-CUP. This stage takes approximately 25 seconds. The 1-CUP button flashes while it runs and remains constant once that stage has finished. If you need to stop it early, press 1-CUP again within those 25 seconds.

5. Descale the steam circuit. Turn the steam dial to the right, toward the steam icon. This stage takes approximately 13 seconds. You can terminate it early by turning the dial back to STANDBY.

6. Descale the hot-water circuit. Turn the steam dial to the left, toward the hot-water icon. This stage takes approximately 8 seconds. Returning the dial to STANDBY stops it early.

7. Repeat the three stages. After the first pass, the book says about half (0.5 litre) of the descale solution should be left in the tank. Repeat the coffee, steam, and hot-water stages (manual steps 4–6) to use the rest of the solution.

8. Rinse the tank and run a clean-water pass. After descaling, remove the water tank and rinse it thoroughly, then refill it with fresh cold water to the maximum capacity (2 litres). Repeat the coffee, steam, and hot-water stages so residual cleaning solution is flushed out. This rinse is not optional. Leftover descaler will taint espresso and is not something you want in a milk wand.

9. Exit Descale mode. Press POWER. The book says this will be indicated by the LED lights switching off.

Reinstall a water filter, fill the tank with fresh water, and put the machine back into ordinary use only after that clean-water flush.

After you finish

Run a short burst of water through the group head with no coffee in the portafilter, and briefly open steam and hot water, to confirm the machine behaves normally. Discard that water. If you still taste or smell descaler, run another clean-water pass through all three circuits before you brew for the cup.

Wipe the steam wand. Empty and rinse the drip tray. If the CLEAN / DESCALE light was solid because the machine asked for a descale, it should no longer be asking for that cycle after a completed procedure. If a light remains in an unexpected state, power the machine down, re-read the relevant section of the manual, and contact Breville support rather than repeating acids through the tank.

How often should you descale?

On this model, Breville’s trigger is the solid CLEAN / DESCALE light, not a date you pick at random. How quickly that light comes on depends on your water and on whether a working filter is in the tank.

The official book is direct: the filter helps prevent scale buildup that can cause blockages and heating problems; replacing it every two months reduces the need to descale; hard-water areas should replace it more often. Breville’s US support page adds a volume limit: 60 days or 10.6 gallons. If you skip the filter, leave an exhausted filter in place, or have very hard municipal water, expect to descale more often.

If shots have slowed, steam has weakened, or the light never seems to come on and you suspect scale, do not invent a homemade vinegar flush as the first move. Confirm the model, use the official powder and the official mode, or ask Breville support. Some later machines use a different descale entry sequence; forcing the BES870 combination on the wrong model will not help.

A short checklist

  • You have a BES870 or BES870XL, not a different Breville or Sage espresso machine.
  • The CLEAN / DESCALE light is solid, not flashing.
  • The water filter is removed from the tank.
  • One official sachet is dissolved in one litre of water.
  • Descale mode: hold 2-CUP, then hold POWER, and wait until POWER, 1-CUP, CLEAN / DESCALE, and HOT WATER / STEAM are solid.
  • Coffee (1-CUP) → steam (dial right) → hot water (dial left).
  • Repeat those three stages to use the remaining solution.
  • Rinse the tank, fill to 2 litres with fresh cold water, and repeat all three stages.
  • Press POWER to exit.
  • Reinstall a filter only after the rinse, then flush once more into the drip tray before you make a drink.

Maintenance is easier when it is boring. A correctly run descale is supposed to be uneventful: a few short stages, a thorough rinse, and a machine that heats and flows the way the manual says it should.

Sources